|
AGE: 1985
SPECIFICATIONS:
Material: CR, HR, P&O
Shear Stress: 50,000 PSI
Coil Width, Max.: 60"
Coil O.D., Max.: 72"
Material Thickness: 0.010" to 0.125"
Line Speed: 600 FPM With Build-Up To 1200 FPM
Line Direction: Right to Left
Mode Of Operation: Pull Thru or Drive Slit
CONSISTING OF:
Entry Coil Car: Floor Standing "L" Type Design, 54.5" Bed
Width, Miller 8" Bore Lift Cylinder, Approx. 12"
From Floor To Bottom Of "V" Cradle, 3 HP AC Motor
With Hydraulic Pump (Less Reservoir)
40,000 Lb. Uncoiler: 11" Dia. Shaft At Forward Bearing,
Mandrel Type Design, 16" to 20" I.D., Hydraulic
Expansion, Sliding Base, Holddown Roll (7.5" Dia.
x 52.5" Face Rubber Covered Roll), AC Motor Feed
Up Drive, Wichita Water Cooled Brake
Entry Unit: Peeler Table, Entry Passline Rolls, Entry
Pinch Rolls (6" x Dia. x 62" Face Width, AC Motor
Driven), Entry Side Guides (Manual Adjustment)
Model SES-IH-1210-7-60 Slitter Heads: (2) Drop-In Design
Heads, 7.00" Dia. x 63" Face Arbors, Single Eccentric
Arbor Adjustment, 10.375" to 12.375" Knife Dia.
Range, 75 HP Reliance DC Motor (1150/2400 RPM,
500 Volt, With Blower, Thru Dodge Reducer With
5.1:1 Ratio)
Model HSW-MD Scrap Winder: 0.500" x 0.125" Strip Capacity,
15" Wide x 34" Dia. Bundle Capacity, 3,000 Lb. Max.
Bundle Weight, Hydraulic Motor Driven, Powered Scrap
Dump
Dump
Model STU-DBDR-60-SF Tension Stand: Combination Drag &
Roll Type, Entry Separator Tooling Bar, Drag Tension
Board With Airbag, Exit Separator Tooling Bar,
Dragboard Assembly Travels To Slitter Head To Grab
Material, Roll Tension Assembly, (2) 16" Dia. x 66"
Face Tension Rolls (Wichita Water Cooled Brake On
Each Roll, Hydraulic Motor Powered Threading Drive),
Spare Set Of New Rolls Included
Hydraulic Crop Shear: 66" L Blade, Exit Passline Roll,
16" Dia. x 68" Face (Rubber Covered)
40,000 Lb. Recoiler: 16" Dia. x 70.5" Face Drum, 20" Dia.
With Bolt On Pads, Hydraulic Grip, Hydraulic
Expansion, Hydraulic Push-Off, Overarm Separator,
300 HP Reliance DC Motor (650/1950 RPM, 500 Volt,
With Blower And Holding Brake), Brad Foote Gearbox
With 20.4:1 Ratio
Exit Coil Car: Floor Standing "L" Type Design, 56" Bed
Width, 6" Bore Lift Cylinder, Approx. 12" From Floor
To Bottom Of "V" Cradle, Coil Retaining Arms,
Self-Contained Hydraulics
Reliance DC Drive Panel: New In 1997, Flexpad 3000 Solid
State Drive
Hydraulic Power Unit
Main Operators Control Panel
Water Recirculating Unit For Uncoiler Brake
NOTE: There is a Small Quantity of Tooling Included with the Line
CONDITION: Removed & In Storage
At Location ...........................
RETURN
to complete inventory display
RETURN
to our home page